At least once a week, the bottle warmer should be cleaned. For descaling, pour 2 ounces of white vinegar into the water chamber and add 4 ounces of cold water.
After every four bottles are produced, it’s crucial to clean the funnel. This “How to Clean Brezza Water Warmer” article will help you ensure that your Formula Pro Advanced formula is dispensed properly. Before starting the daily clean, always thoroughly wash your hands and any surfaces that will be used.
How to Clean Brezza Water Warmer?
here’s a guide on how to clean a Breville Brevia water warmer:
Materials needed:
- White vinegar
- Water
- Soft-bristled brush or sponge
- Microfiber cloth
Step 1: Unplug the water warmer and let it cool completely. Empty any remaining water from the reservoir.
Step 2: Mix a solution of half white vinegar and half water. Fill the water reservoir with the solution, up to the MAX level.
Step 3: Plug in the water warmer and turn it on. Let it heat up until the solution starts to steam.
Step 4: Once the solution has steamed for a few minutes, turn off the water warmer and unplug it.
Step 5: Use a soft-bristled brush or sponge to scrub the inside of the water reservoir, being careful not to damage the heating element. Pay extra attention to any mineral buildup or stains.
Step 6: Empty the vinegar solution and rinse the reservoir thoroughly with clean water.
Step 7: Use a microfiber cloth to wipe down the exterior of the water warmer.
Step 8: Fill the water reservoir with fresh water and turn on the water warmer to flush out any remaining vinegar solution. Once the water has heated up, pour it out and repeat the process until the water runs clear.
Step 9: Your Breville Brevia water warmer is now clean and ready to use again. Remember to descale your water warmer regularly to prevent mineral buildup and prolong its lifespan.
Baby Brezza water warmer temperature settings
The Baby Brezza water warmer has two temperature settings: Room Temperature and Body Temperature.
The Room Temperature setting warms bottles and baby food to the same temperature as the surrounding room, which is typically around 68-72°F (20-22°C).
The Body Temperature setting warms bottles and baby food to the ideal temperature for feeding, which is approximately 98.6°F (37°C).
The Baby Brezza water warmer uses a water bath to warm bottles and baby food, which helps to ensure even heating and prevent hot spots.
It also has a built-in timer that automatically shuts off the warmer after 10 minutes, so you don’t have to worry about overheating your baby’s food or bottles.
Baby Brezza Water Warmer Monthly Descaling Instructions
In order to prevent mineral scale on your Formula Pro Advanced’s inside water heater, do the following:
1. Fill the water tank with 600ml of sterile or pre-boiled cooled water after emptying it and removing the Water Tank.
2. Place a cup bigger than 300ml beneath the funnel and place the Water Tank on top of the machine’s base.
3. Press the “water only” button to dispense if you select “300ml.”
4. Press the “water only” button again to dispense another 300ml when the cup is empty, and place it back under the Funnel.
5. Unplug the machine, remove the Water Tank, and dump it. Allow the machine to idle for four hours.
6. Place the Water Tank back on the base after filling it to the maximum line with sterile or pre-boiled cooled water.
7. Run a 300ml cycle using the “water only” button after plugging in the machine and placing a cup to catch 300ml water. After that, repeat the procedure to run the whole tank of water through the machine by disposing of the water in the cup. You’ve rinsed everything when the “Low Water” indicator lights up.
8. Return to normal use after refilling the water tank with sterile or pre-boiled cooled water.
How to clean baby Brezza formula pro Tips?
Here’s a unique Tips on how to clean the Baby Brezza Formula Pro:
- Unplug the machine and disassemble it. Remove the water tank, formula container, mixing funnel, and any other removable parts.
- Rinse all removable parts with warm water to remove any excess formula or residue.
- Fill a bowl with warm water and a small amount of dish soap. Use a soft-bristled brush to scrub the removable parts thoroughly, paying extra attention to any hard-to-reach areas.
- Rinse all parts thoroughly with clean water and dry them with a clean cloth.
- Use a clean, damp cloth to wipe down the exterior of the Formula Pro. Be sure to wipe away any formula residue or spills.
- If you notice any stubborn stains or buildup, mix a solution of equal parts water and white vinegar. Use a soft-bristled brush to scrub the affected area, then rinse with clean water and dry.
- Reassemble the Formula Pro and run a cleaning cycle. To do this, fill the water tank with water and run the machine as you normally would to make a bottle. This will help flush out any remaining formula residue and ensure that the machine is functioning properly.
- Repeat the cleaning process every 1-2 weeks to keep your Baby Brezza Formula Pro clean and functioning properly.
Special Tips– Wash in a gentle cycle in cold water and allow to air dry if you do not want the costume professionally cleaned. Do not dry your mascot’s body with a dryer.
Additional Tips
- Be sure to follow the manufacturer’s instructions for cleaning and maintenance.
- Never submerge the Formula Pro in water or run it through a dishwasher.
- Use only mild dish soap and avoid harsh chemicals or abrasive sponges.
- If you notice any mold or mildew, contact the manufacturer for further instructions on how to clean and disinfect the machine.
How do you deep clean a Baby Brezza sterilizer?
Wipe down the exterior of the Formula Pro with a dry cloth.
Mix a solution of equal parts water and white vinegar. Use a soft-bristled brush to scrub the affected area, then rinse with clean water and dry.
Reassemble the Formula Pro and run a cleaning cycle.
How do you clean the inside of a Baby Brezza bottle warmer?
Run one heating cycle on setting 5 until any scaling has been eliminated before de-scale by mixing 2oz (60ml) of white vinegar with 4oz (120ml) of cold water in the water chamber. When descaling with vinegar, make sure there is adequate ventilation.
To clean the inside of a Baby Brezza bottle warmer, follow these steps:
- Unplug the bottle warmer and let it cool completely.
- Remove any remaining water from the reservoir.
- Mix a solution of equal parts white vinegar and water.
- Pour the solution into the reservoir of the bottle warmer, filling it up to the MAX level.
- Plug in the bottle warmer and turn it on, allowing it to heat up and steam for about 5-10 minutes.
- Once the solution has steamed, turn off the bottle warmer and unplug it.
- Use a soft-bristled brush or sponge to scrub the inside of the reservoir and the warming chamber. Be gentle, but thorough, and pay attention to any mineral buildup or stains.
- Empty the vinegar solution and rinse the reservoir and warming chamber with clean water.
- Use a microfiber cloth to wipe down the exterior of the bottle warmer.
- Fill the reservoir with fresh water and turn on the bottle warmer to flush out any remaining vinegar solution. Once the water has heated up, pour it out and repeat the process until the water runs clear.
- Your Baby Brezza bottle warmer is now clean and ready to use again.
Additional Tips
- Clean your bottle warmer regularly to prevent mineral buildup and keep it functioning properly.
- Avoid using harsh chemicals or abrasive sponges on the bottle warmer, as this can damage the heating element or other components.
- Follow the manufacturer’s instructions for cleaning and maintenance to ensure optimal performance and prolong the lifespan of your bottle warmer.
Last Word
Cleaning your Baby Brezza bottle warmer is an important part of keeping it in good working order. Follow these simple steps to clean it and keep it functioning properly. I think all information will help you to clean your Baby Brezza Bottle Warmer.